IJAITE- International Journal of Advanced Innovative Technology in Engineering

Archives of International Journal of Advanced Innovative Technology in Engineering(IJAITE)

Volume 1 Issue 1 January 2016

1. CMOS Design Of Tree Multiplier Using Low Power And Area Efficient Full Adder

AUTHOR NAME : MS. S. A. DRAVYEKAR

ABSTRACT : The beginning of Digital electronic with the of vacuum tubes. But implementation of larger engines became economically and practically infeasible. As electrons have higher mobility than holes, NMOS was preferred later so micro processors chip used NMOS-only logic, with higher speed relative to the PMOS logic. But later, NMOS-only logic started suffering from the same problem, power consumption. In case of CMOS, addition of a single input become a greater the device count by 2 and thus maximum the propagation delay. New logic styles were developed to minimize the propagation delay and chip area. In this paper present high-speed and low-power full-adder cells proposed with an alternative internal logic structure and pass-transistor logic styles that lead to have a less power-delay product (PDP). Wallace high-speed multipliers use full adders and half adders in their moderation phase. Half adders do not reduce the number of partial product bits. Therefore, reduce the number of half adders used in a multiplier reduction will minimum the complexity. A modification to the Wallace reductions gives guarantees that the delay is the same as for the conventional Wallace reduction

Download

2. To Study The Solar Chill Refrigeration Technology And Its Challenges & Opportunities

AUTHOR NAME : SUYOG THAKARE

ABSTRACT : Solar energy is one of the renewable source energy. it describe the two distinctive nature one is passive solar and another is active solar. Depending on the way they capture and distribute solar energy or convert it into solar power. Solar power is the conversion of sunlight and it converted into electricity, either directly using photovoltaic’s (PV), or indirectly using concentrated solar power (CSP). Today’s many countries in the world have been use the conventional source of energy for a long time and facing the many problems cause pollution when used, as they emit smoke and ash. Conventional source of energy are very expensive to be maintained, stored and transmitted as they are carried over long distance through transmission grid and lines and it can be exhaustible except water. Due to this we need to conserve these conventional sources and make maximum use of renewable sources. This non-conventional energy sources are now in the process of glowing over the past few years. It includes solar, wind, tidal, biogas, and biomass, geothermal. They are generally pollution free. Less costly due to local use and easy to maintain. for that reason, we focuses only one renewable source of energy i.e. solar chill refrigerator. In this paper, we discuss the solar chill refrigerator technology, its challenges and opportunities.

Download

3. A Rapid Prototyping Technology And Its Applications In Engineering Field: A Review

AUTHOR NAME : NITIN D. GHONGADE, SANDIP S. JAWRE, PRADEEP M. BORADE

ABSTRACT : In Rapid Prototyping model contains different processes which avoids tooling time in manufacturing prototypes or prototype parts and that allows a prototypes to be produced within hours or days rather than weeks. These prototypes are frequently used to check the products technical feasibility or consumer interest. Rapid Prototyping is defined as a set of technologies used to quickly build a scale model of a component using 3-dimensional computer aided design (CAD) software data. Rapid Prototyping decreases development time and corrections is made in product in early stage. Rapid Prototyping is layer-by-layer material deposition started during early 1980s with the tremendous growth in CAD/CAM technology. The edges and surfaces of a complex solid model and their information which is used for describing the product and next the further manufacturing process is completed in CNC machine. The Rapid Prototyping is one of extraordinary technology that reorganizing the making process. The Prototype techniques can also be used to make tooling is said to as rapid tooling and even quality in part. Designers have always used Prototypes and RP allows the user to work faster and it is less expensive. For small production runs and complicated objects, rapid prototyping is a best developing method available. The rapid is a relative term. Most of the prototypes model need a three to seventy two hours for developing. It is depend upon its size and complexity of the component.

Download

4. Solar Based Multiple Mobile Charging Using Voice Indication System With Energy Backup

AUTHOR NAME : MONALI JAWADE, ASHWINI JAGTAP, PRITI NICHADE, PUNAM SARDAR, PROF. S. KAMBLE

Download

5. Three Wheel Vehicle Run With The Help Of Compressed Air, Useing Double Acting Cylinder: A Review Study

AUTHOR NAME : SK. SAMSUDDI, VIVEK V. WANKHAD, PROF. D.R.RANGAR

ABSTRACT : The new era of automobile industry is to design a light weight vehicles. Every automotive industry is looking to reduce the weight of the vehicle as it helps in the better handling of the vehicle and increases the efficiency of the vehicle. Today, the petrol and diesel vehicles are known for producing a large amount of harmful gases like CO2, SO2 etc. which affect the environment. To reduce the global warming or pollution in city or globally, the introducing of compressed air vehicle is a great solution for new generation world. The compressed air is used for fuel in this vehicle. This is one of the alternative fuel sources for propulsion the vehicle with the help of double acting cylinder. Means the car get powered by the help of compressed air. It can put in green revolution in automobile or vehicle world by the help of this project.

Download

6. Study Of Vermicasts From Earthworms

AUTHOR NAME : UMESH GIRDE,PRATIK BHAGAT, VAIBHAV LONKAR, AKASH ANMALWAR, PROF. D.R.RANGARI

ABSTRACT : This paper is for set up the a commercial earthworm business enterprise. Information about vermiculture – raising earthworms in a net and give a food. The detail Information about using these worms, usually Eisenia fetida, it is a process of including waste into vermicompost. Vermicompost is used a such place where earthworm grows, industry as an ingredient in soil mixes and performs pest and disease control functions as a soil alteration. Production and marketing problems are covered up for both types of earthworm businesses. Whether you are raising worms for bait or using them to produce vermicompost, first you will need to study how to raise earthworms. For your worm-based business, you will have to separate section for earthworms to their required environment for growing and sell your product—either the worms or the vermicompost.

Download

7. Embedded Smart Car Security System On Face Captured And Ultrasonic Sensor Using Raspberry Pi

AUTHOR NAME : ASHWINI V. CHANDORE, BHAVANA T. FUSE, PRIYA A. GHADE , LAXMI B. ADI, DR. R.M. TUGNAYAT

ABSTRACT : Embedded Smart Car Security System on Face captured and Ultrasonic sensor using Raspberry Pi is about providing security in terms of driver identification and providing different vehicle control function using raspberry pi. This paper outlines a novel approach for real time face capture for driver identification and accident avoidance. Car security is providing the security in terms of without key authentication for the driver using face capture. Raspberry pi is used to achieve this goal. When someone driving the car then faces capture system obtain image by one small web camera which can be easily placed in the car. Then the captured image is send to the owners email id. Here also added ultrasonic sensor which focuses on building a user friendly device that specializes in detecting intrusions besides doing close range obstacle detection. Automobile safety becomes better by expecting a crash before it occurs and thereby providing additional time to deploy safety technology. Warning can be like buzzer if the driver is approaching a pothole or any obstruction driver may be warned in advance regarding road entails.

Download

8. Tyre Pressure Management System By Automatic Air Filling Machine On 4-Wheeler: A Review

AUTHOR NAME : SAGAR JADHAV, LAVKUSH JADHAV, GANESH DHADKE, ASHISH WAGH,

ABSTRACT : Tyre is the important part of any vehicle because whole body part exert on the tyre . A drop in tire pressure by just a few pounds per square inch (PSI) can result in the reduction of gas mileage, tire life, safety, and vehicle performance .Tyre pressure monitoring system is a primary need for safety concern of any vehicle .Tyre pressure management system (TPMS) gives instruction about pressure in the tyre and help for safety . The driving force behind the tire pressure management system (TPMS) was to solve the incorrect tire pressure situation. Several key objectives were set forth in order to design a product which satisfies the problem and customer’s needs. TPMS needed to have preset pressure settings for different operating conditions. For pulling a heavy load out of an incline at slow speeds, crawling out of soft dirt, or maneuvering through challenging terrain, a lower tire pressure is desired in order to maximize traction.

Download

9. Embedded Smart Car Security System On Face Captured And Ultrasonic Sensor Using Raspberry Pi

AUTHOR NAME : ASHWINI V. CHANDORE, BHAVANA T. FUSE, PRIYA A. GHADE , LAXMI B. ADI, DR. R.M. TUGNAYAT

ABSTRACT : Embedded Smart Car Security System on Face captured and Ultrasonic sensor using Raspberry Pi is about providing security in terms of driver identification and providing different vehicle control function using raspberry pi. This paper outlines a novel approach for real time face capture for driver identification and accident avoidance. Car security is nothing but providing the security in terms of keyless authentication for the driver using face capture. Raspberry pi is used to achieve this goal. When someone driving the car then face capture system obtain image by one tiny web camera which can be hidden easily in somewhere in the car. Then the captured image is send to the owners email id. Here also added ultrasonic sensor which focuses on building a user friendly device that specializes in detecting intrusions besides doing close range obstacle detection. Automobile safety can be improved by anticipating a crash before it occurs and thereby providing additional time to deploy safety technology. Warning can be like buzzer if the driver is approaching a pothole or any obstruction driver may be warned in advance regarding road entails.

Download

10. Automatic Air Filling Machine On 4-Wheeler: A Review

AUTHOR NAME : ASHWADIP K. MESHRAM, RAHUL RADE, UTKARSH BAGESHWAR, SHASHANK RAUT, P. K. CHANNE

Download

11. Study Of Vermicasts From Earthworms

AUTHOR NAME : UMESH GIRDE, PRATIK BHAGAT, VAIBHAV LONKAR, AKASH ANMALWAR, PROF. D. R. RANGARI

ABSTRACT : This publication is for entrepreneurs interested in a commercial earthworm enterprise. Information about vermiculture – raising earthworms for bait or feed – is included. Information about using these worms, usually Eisenia fetida, to process waste into vermicompost is also included. Vermicompost is used in nurseries or the landscape industry as an ingredient in potting soil mixes and performs pest and disease control functions as a soil amendment. Production and marketing issues are covered for both types of earthworm businesses. Whether you are raising worms for bait or using them to produce vermicompost, you will need to learn how to raise earthworms. For your worm-based business, you will have to separate earthworms from their growing environment and sell your product—either the worms or the vermicompost.

Download

12. Solar Based Multiple Mobile Charging Using Voice Indication System With Energy Backup

AUTHOR NAME : MONALI JAWADE, ASHWINI JAGTAP, PRITI NICHADE, PUNAM SARDAR, PROF. S. KAMBLE

Download

13. Automatic Cargo Plant

AUTHOR NAME : PRANALI R. TONGE, CHAITALI S. HANDE, PRIYANKA R. GAYAKWAD, AJAL A. GURU, PROF. S. KAMBLE

ABSTRACT : Radio Frequency Identification (RFID) technology has the potential to dramatically improve numerous industrial practices. However, it still faces many challenges, including security and reliability, which may limit its use in many application scenarios. While security has received considerable attention, reliability has escaped much of the research scrutiny. In this work, we investigate the reliability challenges in RFID-based tracking applications, where objects (e.g., pallets, packages, and people) tagged with low-cost passive RFID tags pass by the RFID readers. Combining with the radio frequency identification (RFID) technology for tracking and trace technology provides an effective solution on the basis of using RFID and ATMEGA 16. Automatic identification and event handling, sharing of items, "transparent" management. RFID based Real Time Location Tracking System (RTLS) for tracking transit goods is discussed. This paper discusses the design and implementation of RTLS for tracking wet cargo, and points out the strengths, benefits, weaknesses and limitations of the solution. The effectiveness of the solution was demonstrated in addressing the weaknesses of the current manual tracking system in curbing diversion for wet cargo. In addition, the use of RTLS led to a reduction in turnaround times by between thirty to forty percent compared to those which are manually tracked.

Download